Author Topic: Replacing slide button  (Read 160 times)

0 Members and 1 Guest are viewing this topic.

Offline Ed McCullough

  • CONTRIBUTOR
  • Chrome-Meister
  • ****
  • Posts: 2,271
Replacing slide button
« on: July 20, 2024, 09:03:26 PM »
I use E6000 glue. It is very tenacious. It has a tiny bit of softness and flex when it is cured. It is never brittle and therefore never breaks.

Offline Age

  • A.J.Fedor
  • HELPER
  • Chrome-Minator
  • ***
  • Posts: 694
  • A.J. Fedor ><((((º> (member since 9/1/22)
Re: Replacing slide button
« Reply #1 on: July 20, 2024, 09:23:31 PM »
I have some of that stuff around here somewhere. It reminds me of Gorilla Glue.
Retired Champion Thread Starter 😎

Offline Ed McCullough

  • CONTRIBUTOR
  • Chrome-Meister
  • ****
  • Posts: 2,271
Re: Replacing slide button
« Reply #2 on: July 20, 2024, 09:26:01 PM »
I use the glue to repair tiny tears and holes in my clothing. Put the glue on the inside of the clothing and mash it into the fabric. Press only lightly, so that you do not see a colored spot when you look at the front of the Garment. This is much faster than sewing.

Offline Ed McCullough

  • CONTRIBUTOR
  • Chrome-Meister
  • ****
  • Posts: 2,271
Re: Replacing slide button
« Reply #3 on: July 20, 2024, 09:27:42 PM »
E6000 also repairs leaks in air mattresses. Use only the glue. You do not have to put a layer of any cover material on top of the glue.

Offline Scotty

  • PRESIDENT'S CLUB
  • MonsterMeister
  • *
  • Posts: 9,764
  • Elizabeth (Scotty)
    • Myspace.com/elizabethgs
Re: Replacing slide button
« Reply #4 on: August 15, 2024, 01:09:44 PM »
I have some of that stuff around here somewhere. It reminds me of Gorilla Glue.

I used Gorilla glue years ago to replace a 260 button. It's still solidly on there.

scotty

Offline Lockjaw Larry

  • Lockjaw Larry ♪♪ Breathing Music daily ♬
  • CHARTER MEMBER
  • Chrome-Minator
  • *
  • Posts: 691
Re: Replacing slide button
« Reply #5 on: August 15, 2024, 08:42:32 PM »
Year before last at Danny’s party my EastTop slide tab popped off ending my jam fun.  I drilled a teeney hole in the bare slide end, affixed the button with epoxy and it is still tight.  The hole gave better purchase for the glue. 
A few years ago I won a bid on a good looking barely played 64 on eBay that had a button missing.  I got it for a very good price and instead of replacing the button I cut a length of .018” shim ( because that’s what I had), affixed it to the wood end with a small screw, and connected it to the slide with a groove I cut in the shim.   While not a beauty it works so well it became my arm chair go to when I need a 16 holer.  No gorilla nor epoxy needed.
Be fair, be square and obey the rules of the pack.

Offline Ed McCullough

  • CONTRIBUTOR
  • Chrome-Meister
  • ****
  • Posts: 2,271
Re: Replacing slide button
« Reply #6 on: August 15, 2024, 10:09:14 PM »
Larry, Sounds like a winner.

Offline brorat

  • PRESIDENT'S CLUB
  • Chrome-Meister
  • *
  • Posts: 2,048
  • Member
Re: Replacing slide button
« Reply #7 on: August 15, 2024, 10:49:11 PM »
Looks like a winner too!
“Just here to harp on chromatics!”

Offline Age

  • A.J.Fedor
  • HELPER
  • Chrome-Minator
  • ***
  • Posts: 694
  • A.J. Fedor ><((((º> (member since 9/1/22)
Re: Replacing slide button
« Reply #8 on: August 16, 2024, 12:35:25 AM »
Man! That's a relic, Lar! Looks like the one I bought myself with my shoe shine money when I was eleven. (I still have it BTW 8))
Retired Champion Thread Starter 😎

Offline Lockjaw Larry

  • Lockjaw Larry ♪♪ Breathing Music daily ♬
  • CHARTER MEMBER
  • Chrome-Minator
  • *
  • Posts: 691
Re: Replacing slide button
« Reply #9 on: August 16, 2024, 06:59:10 AM »
Man! That's a relic, Lar!

Yeah, it’s one of those barn finds that wasn’t over used nor abused.  ‘Cept the button was missing when I bid very low and won it.  Since then it has developed three cracks that I repaired with epoxy glue.  She ain’t purty but, like us olduns, still making sweet moans and groans. 
Be fair, be square and obey the rules of the pack.